From: acevest <zhaoyanbai@126.com>
Date: Sun, 22 Sep 2024 04:11:33 +0000 (+0800)
Subject: 修复当PCI的IDE Controller指定了中断号时而内核因为使用了默认的硬盘中断号导致收不到硬盘中断的问题
X-Git-Url: http://zhaoyanbai.com/repos/doc/%20%22?a=commitdiff_plain;h=3e67f42912c91593843c0184bde6436754fb3979;p=kernel.git

修复当PCI的IDE Controller指定了中断号时而内核因为使用了默认的硬盘中断号导致收不到硬盘中断的问题
---

diff --git a/drivers/ide.c b/drivers/ide.c
index 1bd2658..de5c35c 100644
--- a/drivers/ide.c
+++ b/drivers/ide.c
@@ -105,6 +105,45 @@ SATA（Serial ATA）于2002年推出后，原有的ATA改名为PATA（并行高
 // 随着SATA技术的出现，之前所有的ATA就被称为PATA
 ide_pci_controller_t ide_pci_controller[NR_IDE_CONTROLLER];
 
+void ata_dma_stop(int channel);
+
+void ide_irq_bh_handler(void *arg) {
+    int channel = (int)arg;
+
+    // printk("channel %08x\n", channel);
+    assert(channel <= 1);
+    assert(channel >= 0);
+
+    ide_pci_controller_t *ide_ctrl = ide_pci_controller + channel;
+    // printlxy(MPL_IDE, MPO_IDE, "disk irq %u req %u consumed %u ", disk_inter_cnt, disk_request_cnt,
+    // disk_handled_cnt);
+
+    printlxy(MPL_IDE0 + channel, MPO_IDE, "IDE%d req %u irq %u consumed %u", channel,
+             atomic_read(&(ide_ctrl->request_cnt)), ide_ctrl->irq_cnt, ide_ctrl->consumed_cnt);
+
+    // 之前这里是用up()来唤醒磁盘任务
+    // 但在中断的底半处理，不应该切换任务，因为会引起irq里的reenter问题，导致不能再进底半处理，也无法切换任务
+    // 所以就移除了up()里的 schedule()
+    // 后来就改用完成量来通知磁盘任务，就不存在这个问题了
+
+    // complete会唤醒进程，但不会立即重新调度进程
+    complete(&ide_ctrl->intr_complete);
+}
+
+void ide_irq_handler(unsigned int irq, pt_regs_t *regs, void *devid) {
+    // printk("ide irq %d handler pci status: 0x%02x\n", irq, ata_pci_bus_status());
+    int channel = irq == ide_pci_controller[0].irq_line ? 0 : 1;
+
+    printk("ide[%d] irq %d handler\n", channel, irq);
+
+    ide_pci_controller_t *ide_ctrl = ide_pci_controller + channel;
+    atomic_inc(&ide_ctrl->irq_cnt);
+
+    ata_dma_stop(channel);
+
+    add_irq_bh_handler(ide_irq_bh_handler, (void *)channel);
+}
+
 unsigned int IDE_CHL0_CMD_BASE = 0x1F0;
 unsigned int IDE_CHL1_CMD_BASE = 0x170;
 
@@ -164,6 +203,14 @@ void ide_pci_init(pci_device_t *pci) {
         ide_pci_controller[i].prdt = (prdte_t *)page2va(alloc_one_page(0));
 
         ide_pci_controller[i].pci = pci;
+
+        unsigned int irq_line = pci_read_config_byte(pci_cmd(pci, PCI_INTRLINE));
+        assert(irq_line <= 15);
+        if (irq_line == 0) {
+            ide_pci_controller[i].irq_line = 14 + i;
+        } else {
+            ide_pci_controller[i].irq_line = irq_line;
+        }
     }
 
     IDE_CHL0_CMD_BASE = pci->bars[0] ? (pci->bars[0] & 0xFFFFFFFE) : IDE_CHL0_CMD_BASE;
@@ -172,6 +219,12 @@ void ide_pci_init(pci_device_t *pci) {
     IDE_CHL1_CMD_BASE = pci->bars[2] ? (pci->bars[2] & 0xFFFFFFFE) : IDE_CHL1_CMD_BASE;
     IDE_CHL1_CTL_BASE = pci->bars[3] ? (pci->bars[3] & 0xFFFFFFFE) : IDE_CHL1_CTL_BASE;
 
+    for (int i = 0; i < NR_IDE_CONTROLLER; i++) {
+        int irq = ide_pci_controller[i].irq_line;
+        open_irq(irq);
+        request_irq(irq, ide_irq_handler, "hard", "IDE");
+    }
+
     printd("ide channel 0: cmd %04x ctl %04x\n", IDE_CHL0_CMD_BASE, IDE_CHL0_CTL_BASE);
     printd("ide channel 1: cmd %04x ctl %04x\n", IDE_CHL1_CMD_BASE, IDE_CHL1_CTL_BASE);
 }
@@ -219,43 +272,6 @@ extern void *mbr_buf;
 
 uint8_t ata_pci_bus_status();
 
-void ata_dma_stop(int channel);
-void ide_irq_bh_handler(void *arg) {
-    int channel = (int)arg;
-
-    // printk("channel %08x\n", channel);
-    assert(channel <= 1);
-    assert(channel >= 0);
-
-    ide_pci_controller_t *ide_ctrl = ide_pci_controller + channel;
-    // printlxy(MPL_IDE, MPO_IDE, "disk irq %u req %u consumed %u ", disk_inter_cnt, disk_request_cnt,
-    // disk_handled_cnt);
-
-    printlxy(MPL_IDE0 + channel, MPO_IDE, "IDE%d req %u irq %u consumed %u", channel,
-             atomic_read(&(ide_ctrl->request_cnt)), ide_ctrl->irq_cnt, ide_ctrl->consumed_cnt);
-
-    // 之前这里是用up()来唤醒磁盘任务
-    // 但在中断的底半处理，不应该切换任务，因为会引起irq里的reenter问题，导致不能再进底半处理，也无法切换任务
-    // 所以就移除了up()里的 schedule()
-    // 后来就改用完成量来通知磁盘任务，就不存在这个问题了
-
-    // complete会唤醒进程，但不会立即重新调度进程
-    complete(&ide_ctrl->intr_complete);
-}
-
-void ide_irq_handler(unsigned int irq, pt_regs_t *regs, void *devid) {
-    // printk("ide irq %d handler pci status: 0x%02x\n", irq, ata_pci_bus_status());
-
-    int channel = irq == 14 ? 0 : 1;
-
-    ide_pci_controller_t *ide_ctrl = ide_pci_controller + channel;
-    atomic_inc(&ide_ctrl->irq_cnt);
-
-    ata_dma_stop(channel);
-
-    add_irq_bh_handler(ide_irq_bh_handler, (void *)channel);
-}
-
 void ide_ata_init();
 void ide_init() {
     memset(ide_pci_controller, 0, sizeof(ide_pci_controller[0]) * NR_IDE_CONTROLLER);
@@ -263,10 +279,6 @@ void ide_init() {
     // 读PCI里 IDE相关寄存器的配置
     init_pci_controller(0x0101);
 
-    request_irq(0x0E, ide_irq_handler, "hard", "IDE");
-
-    request_irq(0x0F, ide_irq_handler, "hard", "IDE");
-
     // 读IDE 硬盘的identity
     ide_ata_init();
 }
diff --git a/drivers/ide.h b/drivers/ide.h
index 2c599eb..8cf5125 100644
--- a/drivers/ide.h
+++ b/drivers/ide.h
@@ -190,6 +190,8 @@ typedef struct _ide_pci_controller {
     atomic_t request_cnt;
     atomic_t irq_cnt;
     atomic_t consumed_cnt;
+
+    int irq_line;
 } ide_pci_controller_t;
 
 #define NR_IDE_CONTROLLER 2
diff --git a/kernel/system.c b/kernel/system.c
index 1717762..eab8ccb 100644
--- a/kernel/system.c
+++ b/kernel/system.c
@@ -151,8 +151,9 @@ void setup_irqs() {
     // 打开支持的中断
     open_irq(IRQ_CLOCK);
     open_irq(IRQ_KEYBOARD);
-    open_irq(IRQ_DISK);
-    open_irq(15);
+    // open_irq(IRQ_DISK);
+    // open_irq(15);
+    // open_irq(10);
 }
 
 void boot_irq_handler();