From: Leonardo Fogel Date: Thu, 2 Jul 2015 21:45:04 +0000 (-0300) Subject: eMMC: add support to 8-bit mode. X-Git-Url: http://zhaoyanbai.com/repos/%22http:/www.isc.org/icons/zpipe.c?a=commitdiff_plain;h=4796287659dbd9546688588ed43610eda23d9156;p=minix.git eMMC: add support to 8-bit mode. Change-Id: I0470130eb5f8de319cd55c448a9aa1b9131e8e07 --- diff --git a/etc/system.conf b/etc/system.conf index 75d77c806..15f37ff1f 100644 --- a/etc/system.conf +++ b/etc/system.conf @@ -742,6 +742,7 @@ service emmc system PRIVCTL IRQCTL + PADCONF ; irq 28 # MMCSD1INT diff --git a/minix/drivers/storage/mmc/emmc.c b/minix/drivers/storage/mmc/emmc.c index a693f9b8a..f52715f55 100644 --- a/minix/drivers/storage/mmc/emmc.c +++ b/minix/drivers/storage/mmc/emmc.c @@ -48,12 +48,22 @@ /* The card sector size is 512B. */ #define SEC_SIZE 512 +/* + * AM335x Control Module registers CONF_GPMC_ADn. + * Configuration do multiplex CONF_GPMC_ADn to signals MMC1_DATn (Mode 1). + */ +#define CONF_GPMC_AD(N) (0x800 + 4*(N)) +#define CONF_GPMC_AD_MASK 0x7F +#define CONF_GPMC_AD_VAL 0x31 + /* AM335x MMC1 memory map (physical start address and size). */ #define AM335X_MMC1_BASE_ADDR 0x481D8000 #define AM335X_MMC1_SIZE (4 << 10) /* AM335x MMC1 interrupt number. */ #define AM335X_MMCSD1INT 28 +static uint32_t bus_width; + /* AM335x MMCHS registers virtual addresses: virtual base + offset. */ static struct omap_mmchs_registers *reg; @@ -439,8 +449,8 @@ read_busy(void) { uint32_t stat; /* - * The busy signal is optional, but the host controller will assert - * SD_STAT[1] TC even if the card does not send it. + * The busy signal is optional, but the host controller will assert + * SD_STAT[1] TC even if the card does not send it. */ if (irq_wait() < 0) return -1; @@ -619,6 +629,24 @@ minix_init(void) return 0; } +/* + * Configure the Control Module registers CONF_GPMC_AD4-7. + * Multiplex pins GPMC_AD4-7 to signals MMC1_DAT4-7 (Mode 1). + * Return 0 on success, a negative integer on error. + */ +static int +conf_gpmc_ad(void) +{ + uint32_t i; + + for (i=4; i<8; i++) { + if (sys_padconf(CONF_GPMC_AD(i), CONF_GPMC_AD_MASK, + CONF_GPMC_AD_VAL) != OK) + return -1; + } + return 0; +} + /* * Interface to the MINIX block device driver. * Host controller initialization. @@ -638,6 +666,16 @@ emmc_host_init(struct mmc_host *host) if (minix_init() < 0) return -1; + /* + * Multiplex pins GPMC_AD4-7 to signals MMC1_DAT4-7 (Mode 1), in order + * to allow the use of 8-bit mode. + * U-Boot multiplexes only pins GPMC_AD0-3 to signals MMC1_DAT0-3. + */ + if (conf_gpmc_ad() < 0) + bus_width = EXT_CSD_BUS_WIDTH_4; + else + bus_width = EXT_CSD_BUS_WIDTH_8; + /* Reset the host controller. */ set32(reg->SYSCONFIG, MMCHS_SD_SYSCONFIG_SOFTRESET, MMCHS_SD_SYSCONFIG_SOFTRESET); @@ -676,7 +714,7 @@ emmc_host_init(struct mmc_host *host) /* Enable the bus clock. */ set32(reg->SYSCTL, MMCHS_SD_SYSCTL_CEN, MMCHS_SD_SYSCTL_CEN_EN); - + /* * Set the internal clock gating strategy to automatic, and enable * Smart Idle mode. The host controller does not implement wake-up @@ -810,7 +848,7 @@ emmc_card_initialize(struct sd_slot *slot) /* Card capacity for densities greater than 2GB. */ if (MMC_EXT_CSD_SEC_COUNT > 0) card_size = (uint64_t)MMC_EXT_CSD_SEC_COUNT * SEC_SIZE; - + /* CMD6. Switch to high-speed mode: EXT_CSD[185] HS_TIMING = 1. */ if (mmc_switch(MMC_SWITCH_MODE_WRITE_BYTE, EXT_CSD_HS_TIMING, 1) < 0) return NULL; @@ -832,9 +870,9 @@ emmc_card_initialize(struct sd_slot *slot) /* Set data and busy time-out: ~ 2,8s @ 48MHz.*/ set32(reg->SYSCTL, MMCHS_SD_SYSCTL_DTO, MMCHS_SD_SYSCTL_DTO_2POW27); - /* CMD6. Set data bus width to 4. */ + /* CMD6. Set data bus width. */ if (mmc_switch(MMC_SWITCH_MODE_WRITE_BYTE, EXT_CSD_BUS_WIDTH, - EXT_CSD_BUS_WIDTH_4) < 0) + bus_width) < 0) return NULL; /* Wait for the (optional) busy signal. */ if (read_busy() < 0) @@ -843,8 +881,11 @@ emmc_card_initialize(struct sd_slot *slot) if (send_status() < 0) return NULL; - /* Host controller: set 4-bit data bus width. */ - set32(reg->HCTL, MMCHS_SD_HCTL_DTW, MMCHS_SD_HCTL_DTW_4BIT); + /* Host controller: set data bus width. */ + if (bus_width == EXT_CSD_BUS_WIDTH_4) + set32(reg->HCTL, MMCHS_SD_HCTL_DTW, MMCHS_SD_HCTL_DTW_4BIT); + else + set32(reg->CON, MMCHS_SD_CON_DW8, MMCHS_SD_CON_DW8_8BITS); /* CMD16. Set block length to sector size (512B). */ if (set_blocklen() < 0) diff --git a/minix/drivers/storage/mmc/emmc.txt b/minix/drivers/storage/mmc/emmc.txt index e1ba41456..59c37a593 100644 --- a/minix/drivers/storage/mmc/emmc.txt +++ b/minix/drivers/storage/mmc/emmc.txt @@ -1,17 +1,18 @@ -The eMMC driver was designed to be linked to the existing MMC/SD block device driver (mmcblk.c). +The eMMC driver was designed to be linked to the existing MMC/SD block device +driver (mmcblk.c). * Mini how-to -On the BeagleBone Black, the block device files /dev/c1d* (major = 8) are free. The driver can use /dev/c1d0. +On the BeagleBone Black, the block device files /dev/c1d* (major = 8) are free. +The driver can use /dev/c1d0. # service up /service/emmc -dev /dev/c1d0 -* 4-bit mode (data bus width) -On the BeagleBone Black, the eMMC data lines are connected to the AM335x GPMC_AD[0-7] pins. After PoR, these pins are multiplexed to signals GPIO1_[0-7], and U-Boot only multiplexes pins GPMC_AD[0-3] to signals MMC1_DAT[0-3]. Consequently, 8-bit mode (signals MMC1_DAT[4-7]) can not be used. - * Programmed Input/Output The driver does not have support for DMA. * High capacity cards -Data address for media =< 2GB is byte address, and data address for media > 2GB is sector (512B) address. The driver was designed to handle both address modes, but it was tested on a 2GB card. +Data address for media =< 2GB is byte address, and data address for media > 2GB +is sector (512B) address. The driver was designed to handle both address modes, +but it was tested on a 2GB card. * References BeagleBone Black System Reference Manual, Revision A5.6.